Appliance circuit installation in Minnesota
Correctly sized circuits for your range, dryer, water heater, sump pump and HVAC equipment.
- We size each circuit to the equipment nameplate
- Old three-wire dryer circuits can be updated to four-wire
- We coordinate with your HVAC contractor on connections
- MN License #EA807704
- Bonded & insured
- Permits & inspections handled
- Free quotes
Get your free quote
Two short steps. No obligation.
We will call you to talk through the job and set up your free quote. Need us sooner? Call 612-445-2794.
Your email app should open with your request filled in. Press send, or call 612-445-2794.
Appliance & Equipment Circuits, start to finish
- Range and oven circuits
- Four-wire dryer circuits
- Water heater wiring and disconnects
- Sump and well pump circuits
- Furnace, heat pump and AC connections
- New breaker and panel capacity check
We handle appliance and equipment circuits across Minnesota, including Minneapolis, St. Paul, Bloomington, Edina, Plymouth, Maple Grove, Burnsville, Eden Prairie, Fridley and Minnetonka. See every city we serve.
What our customers say
Real customer reviews from our Google Business Profile, quoted word for word. Harlan Austin, named in some reviews, is one of the company's three partners.
A couple of very nice guys that were straight forward and willing listen to my need and work with what I wanted to get done. They were quick but cleaned up and put everything back after they were done. Could not be happier and will be calling them back any time I need electrical work done.
Harlan was exceptionally thorough in assessing our project needs and advising impartially on the best path forward. Would highly recommend.
Great experience all around! High quality work, great communication, detail-oriented, kind. Would hire again in a heartbeat.
Three steps to a finished job
Tell us what you need
Call 612-445-2794 or send the short form. Quotes are free.
Get a written scope and price
We look at the job and put the scope and price in writing before any work starts.
We do the work and get it inspected
We pull the permit, do the work, and the inspector signs off.
Common questions
Should I have the circuit done before the appliance arrives?
Can I use my existing dryer or range outlet for a new appliance?
Why do some appliances need a separate shut-off?
Does a sump pump need special wiring?
Want the details first? Read our guide: Apartment Unit Turnover Electrical Checklist for Property Managers.
More about appliance and equipment circuits
Appliances and fixed equipment are not interchangeable when it comes to electrical supply. An electric range, a dryer, a wall oven, an electric water heater and a heat pump each have a different voltage, amperage and connection type. Using the wrong cable or breaker size is a safety problem and can void the manufacturer's instructions.
This page is about the circuits that serve specific equipment already in your home or about to be. A new range may need a 240V circuit where a gas range sat before. A dryer swap may reveal an old three-wire receptacle that is no longer acceptable for a new installation. A basement sump pump needs power that stays reliable during storms and meltwater. Finding those problems before the appliance arrives saves a delivery day.
We work from the appliance's nameplate or installation sheet and from the existing wiring. When a circuit already exists, we check that it is the right size and in good condition. When it does not, we install a new one on its own breaker. This is a more specific service than general dedicated circuit work, so if you have an unusual load, start with the dedicated circuits page.
When you need it
- You are converting from a gas range, dryer or water heater to electric and need 240V at that location.
- A new appliance has a different plug or connection from the existing receptacle.
- Your dryer or range outlet is a three-slot type, scorched, loose or has a cord that runs warm.
- A sump pump, freezer or well pump shares a circuit with other loads and a trip would be costly.
- A new heat pump, furnace, boiler or air conditioner needs a disconnect and a correctly sized circuit.
- A built-in microwave, dishwasher or disposal needs its own circuit in a kitchen remodel.
- An existing appliance is in a location where the breaker keeps tripping when it runs.
What’s included, in detail
240V circuits and receptacles for ranges, cooktops and wall ovens, sized to the nameplate.
A proper four-wire dryer circuit and receptacle, replacing outdated three-wire arrangements when the work calls for it.
Dedicated 240V circuits and disconnects for electric tank and tankless water heaters.
Dedicated circuits with proper ground-fault protection for pumps in basements and utility spaces.
Circuits and service disconnects for furnaces, heat pumps, air conditioners and boilers, coordinated with your HVAC contractor.
Separate circuits for dishwashers, disposals, microwaves and washing machines.
A new breaker and panel capacity check for every circuit we add.
Our process
- Check the equipment
We review the nameplate or installation instructions and look at the existing circuit.
- Decide reuse or replace
We tell you whether the current wiring is suitable or whether a new circuit is needed.
- Wire and connect
We install the circuit, receptacle or hardwired connection, and set the breaker size.
- Test and sign off
We test under load, confirm the inspection is passed where required and label the panel.
More questions
Will you coordinate with my appliance installer or HVAC contractor?
Guides
Often done together
Appliance and equipment circuits work often goes together with equipment connections; dedicated circuits; and commercial kitchen electrical. We can quote them together.
Ready for your free circuit quote?
Call or send the short form. You get a written scope and price before any work starts.